MANUAL, Pls visit: http://www.mateksys.com/downloads/HUBOSD8-H_EN.pdf
About STOSD,pls visit: http://www.stosd.com

The BEC 12V is linear regulator, no LC Filter needed. Built-in STOSD8 can support Plug andamp; Play, no complicated settings needed.

General:
Input voltage range (3S-5S operation): 8 - 21VDC
PDB: 4x30A (Max.4x35A)
Reglated 5V and 12V outputs
Current Sensor 140A
Built-in STOSD8

Physical:
- 2oz copper, 4-layers andamp;1.6mm PCB.
- 1x Battery input, 4x ESC outputs. 2x BEC 5V outputs, 2x BEC 12V outputs.
- Camera signal andamp; Gnd pads, Video Transmitter Signal andamp; Gnd pads
- 1x Serial port (RX, TX, G)
- Dimensions: 46x36x4mm, Weight: 8.5g
- Mounting holes 30.5mm square spacing，Φ3mm

PDB(ESC outputs)
Continuous current: 30A per output
Peak current (10 seconds/minute): 35A per output

BEC 5V outputs
Designed for RC Receivers, Flight controllers, OSD, and Servos.
DC/DC synchronous buck regulator.
Voltage: 5.0 +/- 0.1VDC
Continuous current: 2 Amps (Max.2.5A 10s/minute)
Output Ripple: 40mV (VIn=16V, VOut=5V2A load)
Short-circuit tolerant (5 seconds/minute)


BEC 12V outputs
Linear regulator, very low noise. LC Filter is needless.
Designed for Video TX or FPV camera.
Voltage: 12.0 +/- 0.3VDC (4~5S operation)
Continuous current: 500mA16V IN, 400mA20V IN
Short-circuit tolerant (2 seconds/minute)
If the battery is 3S LiPo, Output voltage=3S LiPo voltage - 1V
Current Sensor :140A, If current >140A. STOSD display 140A

--------------------------------------
Package Including
1 * Matek HUBOSD Multifunctinal HUB with PDB BEC 5V 12V

Matek 2PCS MCU CF Dual Mode RGB RC LED Light: https://www.amazon.com/dp/B01EACO4JQ
4pcs 1.5W Super Bright RC LED Light:http://www.amazon.com/dp/B01HGK3Z9E

• A multifunctional HUB with PDB, BEC 5V/2A 12V/500mA,Current sensor 140A, STOSD8.The BEC 12V is linear regulator, no LC Filter needed. Specially made for the mini FPV Quad.
• Built-in STOSD8 can support Plug Play,no complicated settings needed.Features:Running indicator, Autodetect PALNTSC, Dynamic on screen info, Min.Volt Max.Amp recorder, Automatic flight timer, Auto battery cells detection, Low vlotage alarm, Exceeding mAh alarm,Firmware upgradable.
• 8 - 21V DC input voltage range(3S - 5S operation). PDB(ESC outputs): 4x30A (Max.4x35A). Regulated 5V and 12V. 140A current sensor.
• 2oz copper.4-layers 1.6mm PCB.Dimensions: 51x36x4mm.Weight: 9g.Mounting holes 30.5mm square spacing,Φ3mm.
• Physical: 1x Battery input,4x ESC outputs.2x BEC 5V outputs,2x BEC 12V outputs,Camera signal Gnd pads,Video Transmitter Signal Gnd pads,1x Serial port (RX, TX, G).

A multifunctional HUB with PDB, BEC 5V/2A 12V/500mA,Current sensor 140A, STOSD8.The BEC 12V is linear regulator, no LC Filter needed. Specially made for the mini FPV Quad.Matek